KBS Coatings 4302 Satin Black RustSeal - 1 Pint

I bought a 2011 truck recently that had spent enough time in salt that it needed to be taken care of. I sand blasted the frame and a friend at work had recommended KBS. I have never used a product like this. It's almost like it forms a hard shell over the metal, not like just painting it. It came out wonderful and would recommend it to anyone. I am now going to order more and continue up the frame. Word to the wise, use it out of a different container. If you get KBS on the lid of the container, it will not open again. Yes, I made that mistake but this is a minor issue compared to the quality finish you get with this product.

The media could not be loaded. Great product. Covers well. No complaints.

Painted a 6” I beam that was seriously rusted. After cleaning it up and painting it, it not only looks good but it’s sealed very nicely now. Should get many more years out of it.

Would spray it next time. Hard to get it not to leave brush marks. Make sure you stir it with a paint stick before each use. Semi-gloss tends to separate and settle at the bottom of can.

I used this to protect various parts on my 93 Jeep Yj mostly on parts of the frame and bumpers where surface rust had started to form over the years. I prepped all of the surfaces with a wire wheel, phosphoric acid, degreaser, this product, then I top coated the areas that are exposed to direct sun with a black satin spray paint.This product went on easily, covered well, and after a few coats was as hard as a rock. I'm truly impressed.I choose to store this product in a glass mason jar, instead of the original can, it made the cleanup and seal/unseal process much easier. Just clean the lid and make sure the top rim is completely clear of product before sealing it up, good to go.

Love the stuff, I have used it to coat my firewall and frame on my 1967 Camaro. The stuff is amazing tough once its cured but not the most beautiful finish. The prep when applying this is very important, if you read the instructions it sounds like you just clean the surface of lose material, degrease, and apply but I had a lot of issues with it not adhering well if I just did this. On the firewall I sanded most of it down to bare metal, degreased, and then used their metal prep and it worked great, for the frame I had to sand blast it first then degreased & metal prep.The other thing with this that I found is if I used a brush the pieces got pulled out of the brush and stuck in the paint and it left very obvious streaks in the paint. I switched to foam brushes and they worked better and did not streak near as much but they can leave piece of foam in the paint that is hard to remove and they do not last. I ended up coating both surfaces (firewall and frame) with 3 to 4 coats of semi-gloss black Rustoleum spray paint to cover the streaks, this left a very nice finished product.Also don't get it on yourself or anything else and if you do immediately clean it off, it takes weeks to wear off of your body. Also once you open the can it can be very hard to re-open it, it tends to seal itself and re-opening can leaves it ruined. I poured it into a glass jar to save.

I love this paint, no mixing, no priming, low fumes. sets fairly quick and dries hard overnight, from what I can tell, it's like a bed liner coating, very tough, but without the lumps.

Exceeded my expectations. Works extremely well on raw iron. Would recommend and expect to purchase again

As advertised. Best to apply with a brush that can be thrown away afterwards. Not good in a spray gun (will ruin it for good). Wear OLD clothes and DO NOT get on your skin as it will not clean off. Very tough finish if used properly. I used a rust converter as a primer and then coated over that. Be sure to clean off loose rust before any application of any product. The coating is a tough as any epoxy and maybe even better. Be sure to put cling wrap over can to close it up so the metal top does not contact the metal can. If you don't use the cling wrap, the can will never open again.

Used this product for the first time, on my 2011 Chev Silverado. Aside from having difficulty getting lid off of 1 qt can, I am very much impressed with the application, and the look and texture of the finished product. I will put a second coat on , just because I have lots of product left. The more I apply , why not.

Bon produit

Very good product, woks well on high high parts

heard this product is awsome....and it really seems to be....time will tell..wear gloves.....again...wear gloves.This product only comes off skin with alot of rubbing with sandpaper....ya...outch...